Question 1

What is wood checking and should I be concerned about it?

Accepted Answer

If you notice small cracks or splits appearing along the surface of your timber beams after installation, you're seeing what woodworkers call checking — and it's completely normal.What causes checking:As kiln-dried timber continues to acclimate to outdoor humidity and temperature conditions, the outer layers of the wood dry faster than the interiorThis differential drying creates tension in the wood fiber that releases as small surface cracks along the grainChecking is most common in the first 12–18 months after installation and typically stabilizes after the wood fully acclimatesShould you be concerned?No — surface checking is cosmetic only and has no effect on the structural performance of your timber frameChecking has been a known and accepted characteristic of solid timber construction for centuriesEven large checks that run several inches along a beam do not compromise load-bearing capacityHow to minimize checking:Apply a quality penetrating wood sealant soon after installation — this slows the rate of moisture change in the outer wood layers and reduces the severity of checkingEnd-seal the cut ends of beams and rafters, where moisture enters and exits most rapidlyAvoid painting your timber frame — paint traps moisture and can accelerate checking rather than prevent it

Question 2

How do I prepare my timber frame pavilion for winter?

Accepted Answer

With proper preparation, a NORWEH timber frame pavilion performs beautifully through winter — whether you're dealing with snow, freeze-thaw cycles, or heavy rain. Here's what to do heading into cold weather.Fall winterization checklist:Inspect and tighten all hardware – wood expands and contracts through the season; check that bolts and post bases are secureClear the roof – remove leaves and organic debris from the roof surface and any gutters; trapped moisture accelerates decayCheck and reseal if needed – fall is the ideal time to apply a fresh coat of wood sealant before freezing temperatures set inEnsure positive drainage – verify that water drains away from post bases; standing water that freezes can damage post base hardware and the wood around itRemove or secure accessories – bring in cushions, string lights, and any removable decor that could be damaged by ice or heavy snowDuring winter:Clear heavy snow accumulation from the roof promptly — while Douglas Fir can handle significant snow load, excessive drifting or ice dam buildup adds unnecessary stressUse a roof rake with a soft head to avoid scratching or damaging your roofing materialAvoid using metal shovels or tools on timber surfaces

Question 3

How do I maintain and protect my timber frame pavilion?

Accepted Answer

Douglas Fir is a naturally durable and beautiful wood, but like all outdoor timber it benefits from regular care to maintain its appearance and maximize its lifespan. The good news: maintenance is straightforward and infrequent.Annual maintenance checklist:Clean the timber surface – wash with a mild wood cleaner or diluted dish soap and a soft brush; rinse thoroughly and allow to dry completelyInspect all hardware – check bolts, lag screws, and post base hardware for any signs of corrosion or loosening; tighten as neededCheck the roof – inspect roofing material for any lifted panels, cracked shingles, or areas where water could penetrateClear debris from roof and gutters – leaves and organic matter hold moisture against timber surfacesInspect post bases – ensure posts are not in contact with standing water or soilEvery 2–3 years:Apply a quality UV-resistant wood sealant or stain – this is the single most important maintenance task; it protects against UV graying, moisture penetration, and surface checkingClean the surface thoroughly and allow to dry for 48–72 hours before applying any sealant or stainUse a product rated for exterior softwood timber — penetrating oil-based stains offer excellent protection and are easy to reapply

Question 4

Do I need to seal or stain my NORWEH timber frame pavilion?

Accepted Answer

While Douglas Fir is a naturally durable and dense wood, applying a sealant or stain is strongly recommended for any timber frame structure installed outdoors. Without a protective finish, even the highest quality wood will eventually show UV graying, surface checking, and moisture absorption.What happens without sealing:UV exposure causes the wood surface to silver-gray over 6–12 months — which some owners appreciate as a natural patina, while others prefer to prevent itMoisture cycling (wet and dry seasons) causes surface checking — small cracks along the grain that are cosmetic rather than structural, but can be minimized with proper sealingUntreated end grain (beam ends and rafter tails) is particularly vulnerable to moisture absorption and should be sealed as a priorityRecommended sealing approach:Apply your first coat of sealant or stain after the wood has had 2–4 weeks to dry and settle after delivery — fresh kiln-dried timber benefits from a brief acclimation periodApply before the first significant rain season in your areaUse a penetrating oil-based exterior wood stain with UV inhibitors for best performance on Douglas FirApply to all exposed surfaces including end grain, post bases, and the underside of raftersReapply every 2–3 years or when water no longer beads on the surface

Free Shipping on All Orders

100 Day Risk-Free Trial

10 Year Guarantee

Speak To An Expert

Speak To An Expert

Maintenance & Care

What is wood checking and should I be concerned about it?

How do I prepare my timber frame pavilion for winter?

How do I maintain and protect my timber frame pavilion?

Do I need to seal or stain my NORWEH timber frame pavilion?

Quick Links

Contact Details

Social Media

Join the NORWEH Timber Frame Community

Sign up for expert tips and exclusive updates

Black Friday – Our Best Deals Ever!

Sign up for our biggest sale of the year.

Social Media